rk3588sHDMI输出点亮屏幕总结

1、问题就是rk358shdmi输出不能点亮屏幕

查看串口输出主要报错：

[    1.710423][    T1] fuse: init (API version 7.32)
[    1.731824][    T1] Key type asymmetric registered
[    1.731831][    T1] Asymmetric key parser 'x509' registered
[    1.731844][    T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 242)
[    1.731848][    T1] io scheduler mq-deadline registered
[    1.731852][    T1] io scheduler kyber registered
[    1.731883][    T1] io scheduler bfq registered
[    1.732276][    T1] rockchip-csi2-dphy-hw fedc0000.csi2-dphy0-hw: csi2 dphy hw probe successfully!
[    1.732347][    T1] rockchip-csi2-dphy-hw fedc8000.csi2-dphy1-hw: csi2 dphy hw probe successfully!
[    1.737658][    T1] rockchip-hdptx-phy-hdmi fed60000.hdmiphy: can't request region for resource [mem 0xfed60000-0xfed61fff]
[    1.737670][    T1] rockchip-hdptx-phy-hdmi: probe of fed60000.hdmiphy failed with error -16-----------------------------------------------这里报错
[    1.738932][    T1] pwm-backlight backlight: supply power not found, using dummy regulator
[    1.739152][    T1] iep: Module initialized.
[    1.739180][    T1] mpp_service mpp-srv: 0e80c24154 author: rd02 2023-11-14 rk3588 basecode sync time:20231114
[    1.739185][    T1] mpp_service mpp-srv: probe start
[    1.740280][    T1] mpp_vdpu2 fdb50400.vdpu: Adding to iommu group 1
[    1.740477][    T1] mpp_vdpu2 fdb50400.vdpu: probe device
[    1.740562][    T1] mpp_vdpu2 fdb50400.vdpu: reset_group->rw_sem_on=0

分析：can't request region for resource [mem 0xfed60000-0xfed61fff]  根据这句打印 可以判断是内存分配冲突了  也就是被占用  ，操作dts删除被占用的设备即可，

解决办法：

&hdptxphy0 {

/* Single Vdiff Training Table for power reduction (optional) */

training-table = /bits/ 8 <

/* voltage swing 0, pre-emphasis 0->3 */

0x0d 0x00 0x00 0x00 0x00 0x00

0x0d 0x00 0x00 0x00 0x00 0x00

0x0d 0x00 0x00 0x00 0x00 0x00

0x0d 0x00 0x00 0x00 0x00 0x00

/* voltage swing 1, pre-emphasis 0->2 */

0x0d 0x00 0x00 0x00 0x00 0x00

0x0d 0x00 0x00 0x00 0x00 0x00

0x0d 0x00 0x00 0x00 0x00 0x00

/* voltage swing 2, pre-emphasis 0->1 */

0x0d 0x00 0x00 0x00 0x00 0x00

0x0d 0x00 0x00 0x00 0x00 0x00

/* voltage swing 3, pre-emphasis 0 */

0x0d 0x00 0x00 0x00 0x00 0x00

>;

status = "okay";

};

&mpp_srv {

status = "okay";

};

&combphy0_ps {

status = "okay";

};

烧录固件  测试OK，问题解决了

问题解决了！！