Dell 错误代码（供参考）我试过报E1410 却是坏阵列卡杯具

最新推荐文章于 2024-09-11 21:40:39 发布

转载最新推荐文章于 2024-09-11 21:40:39 发布 · 1.4w 阅读

标签

#dell #system #action #initialization #timer

本文详细列举了Dell服务器的各种错误代码及其含义，包括电缆和板卡、温度、电压、风扇、处理器等方面的问题，并提供了相应的解决建议。

开发板推荐：天空星STM32F407VET6开发板

超高性价比 STM32主控 | 超高主频 | 一板兼容百芯 | 比赛神器 | 沉金彩色丝印

点击查看

Dell 错误代码（供参考）我试过报E1410 却是坏阵列卡杯具

(2011-06-07 12:46:04)

转载▼

标签：

it

Dell的服务器太多,每次都得上dell的网站查找代码,索性直接粘贴过来

Cable and Board Presence - Message Code: "x1Axx"
Message Code	Message String	Message Priority	Message Comments	Minimum Action Required to Remove Message from LCD	Exists in SEL?	System Phase When Event Can Occur?
E1A10	PDBPwrCable	High	PDB power cable to the planar is missing or bad and system will not power on.	Failing device is reseated/replaced/repaired.	Yes	Pre-Post
E1A11	PCIRsrConfig	High	PCI risers are not configured correctly; some invalid configurations prevent system power on.	Failing device is reseated/replaced/repaired.	Yes	Pre-Post
E1A12	PCIRsrMissing	High	One or all of the PCI risers is missing. This prevents system power on.	Failing device is reseated/replaced/repaired.	Yes	Pre-Post
E1A14	SAS Cable A	Low	SAS cable A is missing or bad.	Failing device is reseated/replaced/repaired.	Yes	Any
E1A15	SAS Cable B	Low	SAS cable B is missing or bad.	Failing device is reseated/replaced/repaired.	Yes	Any
E1A16	SAS Cable FB	Low	Flex bay SAS cable is missing or bad.	Failing device is reseated/replaced/repaired.	Yes	Any
E1A17	PwrCable FB	Low	Flex bay power cable is missing or bad.	Failing device is reseated/replaced/repaired.	Yes	Any
E1A18	PDBCtrl Cable	High	PDB control cable to the planar is missing or bad and system will not power on.	Failing device is reseated/replaced/repaired.	Yes	Any

Temperature - Message Code: "x11xx"
Message Code	Message String	Message Priority	Message Comments	Minimum Action Required to Remove Message from LCD	Exists in SEL?	System Phase When Event Can Occur?
E1114	Temp Ambient	Med	Ambient temperature has a reached a point outside of the allowed range.	Temperature returns to allowable range.	Yes	Any
E1116	Temp Memory	High	Memory has exceeded allowable temperature and has been disabled to prevent damage to the components.	AC Cycle or SEL clear	Yes	Any

Voltages - Message Code: "x12xx"
Message Code	Message String	Message Priority	Message Comments	Minimum Action Required to Remove Message from LCD	Exists in SEL?	System Phase When Event Can Occur?
E1210	CMOSBatt	Low	CMOS battery is missing or the voltage is outside of the allowable range.	Failing device is reseated/replaced/repaired.	Yes	Any
E1211	ROMBBatt	Low	PERC5I RAID battery charger has reported to the Server Management that the battery is either missing, can't charge the battery (possibly because of high temperatures), or the battery is bad.	Failing device is reseated/replaced/repaired.	Yes	Any
W1228	ROMBBatt< 24 hr	Low	This is a predictive failure warning message telling the user that the PERC5I RAID battery has less then 24 hours of charge left init. We provide this message as a warning message to the customer.	Battery charges to > 24 hours of sustained charge.	Yes	Any
E1214	1.5VPwrGd	High	1.5 VV voltage regulator has failed.	AC Cycle or SEL clear	Yes	Any
E1215	1.8VPwrGd	High	1.8 VV voltage regulator has failed.	AC Cycle or SEL clear	Yes	Any
E1216	3.3VPwrGd	High	3.3 V voltage regulator has failed.	AC Cycle or SEL clear	Yes	Any
E1217	5VPwrGd	High	5 V voltage regulator has failed.	AC Cycle or SEL clear	Yes	Any
E1218	PCIRsr5VPwrGd	High	PCI Riser 5 V voltage regulator has failed.	AC Cycle or SEL clear	Yes	Any
E1219	BackplanePwrGd	High	Backplane voltage regulator has failed.	AC Cycle or SEL clear	Yes	Any
E1221	Flex BayPwrGd	High	Flex Bay voltage regulator power good has failed.	AC Cycle or SEL clear	Yes	Any
E1222	VCACHE #PwrGd	High	VCACHE # voltage regulator has failed.	AC Cycle or SEL clear	Yes	Any
E1223	VRM #PwrGd	High	VRM # voltage regulator has failed.	AC Cycle or SEL clear	Yes	Any
E1225	ESB 1.5VPwrGd	High	ESB 1.5 VV voltage regulator has failed.	AC Cycle or SEL clear	Yes	Any
E1226	PCIRsr1.5VPwrGd	High	PCI Riser 1.5 VV voltage regulator has failed.	AC Cycle or SEL clear	Yes	Any
E1227	LinearPwrGd	High	Linear voltage regulator(s) has failed. Represents status of multiple voltage regulators used in the video and LOM circuitry.	AC Cycle or SEL clear	Yes	Any
E1228	0.9VPwrGd	High	Memory VTT voltage regulator has failed.	AC Cycle or SEL clear	Yes	Any
E1229	CPU # VCORE	High	Processor # VCORE voltage regulator has failed.	AC Cycle or SEL clear	Yes	Any
E122A	CPU VTTPwrGd	High	Processor VTT voltage regulator has failed.	AC Cycle or SEL clear	Yes	Any
E122B	0.9 V Over Voltage	High	0.9 V regulator voltage has exceeded the allowable voltage range.	AC Cycle or SEL clear	Yes	Any
E122C	CPU Power Fault	High	A voltage regulator failure was detected when the processor regulator(s) was enabled.	AC Cycle or SEL clear	Yes	Any

Fans - Message Code: "x13xx"
Message Code	Message String	Message Priority	Message Comments	Minimum Action Required to Remove Message from LCD	Exists in SEL?	System Phase When Event Can Occur?
E1310	RPM Fan ##	Low	RPM of fan ## is outside of the intended operating range.	Fan RPM reading returns to a point inside of the intended operating range.	Yes	Any
E1311	RPM Fan Mod #A	Low	RPM of fan A in the # module is outside of the intended operating range.	Fan RPM reading returns to a point inside of the intended operating range.	Yes	Any
E1311	RPM Fan Mod #B	Low	Same as above except for fan B of module #.	Fan RPM reading returns to a point inside of the intended operating range.	Yes	Any
E1311	RPM Fan Mod #C	Low	Same as above except for fan C of module #.	Fan RPM reading returns to a point inside of the intended operating range.	Yes	Any
E1311	RPM Fan Mod #D	Low	Same as above except for fan D of module #.	Fan RPM reading returns to a point inside of the intended operating range.	Yes	Any
E1313	Fan Redundancy	Low	The system is no longer fan redundant. Another fan failure would put the system at risk of over-heating.	Fan redundancy is regained, which requires all fans to be operating within the intended operating range.	Yes	Any

Processors - Message Code: "x14xx"
Message Code	Message String	Message Priority	Message Comments	Minimum Action Required to Remove Message from LCD	Exists in SEL?	System Phase When Event Can Occur?
E1410	CPU # IERR	High	Processor # has had an internal error (IERR), but this does not always mean that CPU is the problem .There are a large variety of issues that cause an IERR.	AC Cycle or SEL clear	Yes	Any
E1414	CPU #Thermtrip	High	Processor # has encountered a Thermtrip(over-temperature) event.	AC Cycle or SEL clear	Yes	Any
E1418	CPU # Presence	High	Processor # is missing/bad and the system is in an unsupported configuration.	AC Cycle or SEL clear	Yes	Pre-POST
E141C	CPU Mismatch	High	Processors are not compatible as defined by Dell .System is in an unsupported configuration.	AC Cycle or SEL clear	Yes	Pre-POST
E141F	CPU Protocol	High	BIOS has reported a processor protocol error.	AC Cycle or SEL clear	Yes	POST, After POST
E1420	CPU Bus PERR	High	BIOS has reported a processor bus PERR (parity error).	AC Cycle or SEL clear	Yes	POST, After POST
E1421	CPU Init	High	BIOS has reported a processor initialization error.	AC Cycle or SEL clear	Yes	POST, After POST
E1422	CPU MachineChk	High	BIOS has reported a machine check error.	AC Cycle or SEL clear	Yes	POST, After POST

System Memory - Message Code: "x21xx"
Message Code	Message String	Message Priority	Message Comments	Minimum Action Required to Remove Message from LCD	Exists in SEL?	System Phase When Event Can Occur?
E2110	MBECrdx DIMM ## & ##	High	One of the DIMMs in the set implicated by "## & ##" has had a multi-bit error (MBE).If no memory riser is present the “Crdx” string is left out of the message.“x” is the memory riser, A-Z.	AC Cycle or SEL clear	Yes	POST, After POST
E2111	SBE Log DisableCrdx DIMM ##	High	BIOS has disabled memory single-bit error (SBE) logging and will not log anymore SBEE's until the system is rebooted.## represents DIMM implicated by BIOS .If no memory riser is present the “Crd x” string is left out of the message.“x” is the memory riser, A-Z.	System reset	Yes	POST, After POST
E2112	MemSpareCrdx DIMM ##	High	BIOS has spared the memory because it has determined the memory had too many errors.## represents DIMM implicated by BIOS. If no memory riser is present the “Crdx” string is left out of the message.“x” is the memory riser, A-Z.	System reset	Yes	POST, After POST
E2113	Mem Mirror Crd x DIMM ## & ##	High	BIOS has disabled memory mirroring because it has determined one half of the mirror has had too many errors. ## & ## represents DIMM pair implicated by BIOS. If no memory riser is present the “Crdx” string is left out of the message.“x” is the memory riser, A-Z.	System reset	Yes	POST, After POST
I2114	MemRaid	Low	BIOS Memory RAID Bank	User action, sensor return to normal	Yes	Any
I2115	MemAdded Card x	Low	Memory has been added while the system is running.	AC Cycle or SEL clear	Yes	Any
I2116	MemRemoved	Low	Memory has been removed while the system is running.	AC Cycle or SEL clear	Yes	Any
E2117	MemHot Plug	Low	Memory hot-plug operation has failed.	AC Cycle or SEL clear	Yes	Any
E2118	Fatal NBMemCRC	High	Northbound FBD CRC error on non-redundant entry. One of the connections in the FBD link on the Northbound (towards the MCH) side is "broken".This is determined by the MCH when two CRC errors have been detected twice in a row.	AC Cycle or SEL clear	Yes	POST, After POST
E2119	Fatal SBMemCRC	High	FBD alert on non-redundant entry. One of the connections in the FBD link on the Southbound (towards the AMB'son the FBDIMM's) side is "broken".This is determined by the MCH when two CRC errors have been detected twice in a row.	AC Cycle or SEL clear	Yes	POST, After POST

Power Supplies - Message Code: "x16xx"
Message Code	Message String	Message Priority	Message Comments	Minimum Action Required to Remove Message from LCD	Exists in SEL?	System Phase When Event Can Occur?
E1610	PS # Missing	Low	Power supply # was removed or is missing from the system.	Failing device is reseated/replaced/repaired.	Yes	Any
E1614	PS # Status	Low	Power supply # has failed.	Failing device is reseated/replaced/repaired.	Yes	Any
E1618	PS # Predictive	Low	Power supply # has a failure that predicts a power down event in this supply (i.e. power supply fan failure or power supply over-temp).	Failing device is reseated/replaced/repaired.	Yes	Any
E161C	PS # Input Lost	Low	Power supply # is attached to the system but has lost its AC/DC input.	Failing device is reseated/replaced/repaired.	Yes	Any
E1620	PS #Input Range	Low	Power supply #'s AC/DC input is outside of the allowable range.	Failing device is reseated/replaced/repaired.	Yes	Any
E1624	PS Redundancy	Low	The power supply subsystem is no longer redundant. If the last supply fails the system will go down.	Failing device is reseated/replaced/repaired.	Yes	Any
E1625	PS AC Current	Low	The power supply input power is above the allowed amount for the power supply.	Failing device is reseated/replaced/repaired.	Yes	Any

BIOS - Message Code: "x17xx"
Message Code	Message String	Message Priority	Message Comments	Minimum Action Required to Remove Message from LCD	Exists in SEL?	System Phase When Event Can Occur?
E1710	I/O ChannelChk	High	BIOS has reported an I/O channel check.	AC Cycle or SEL clear	Yes	POST, After POST
E1711	PCI PERR B## D## F##	High	BIOS has reported PCI parity error on a component that resides in PCI configuration space at bus ##, device ##, function ##.	AC Cycle or SEL clear	Yes	POST, After POST
E1711	PCI PERR Slot #	High	BIOS has reported PCI parity error on a component that resides in slot #.	Same as above.	Same as above.	Same as above.
E1712	PCI SERR B## D## F##	High	BIOS has reported a PCI system error on a component that resides in PCI configuration space at bus ##, device ##, function ##.	AC Cycle or SEL clear	Yes	POST, After POST
E1712	PCI SERR Slot #	High	BIOS has reported a PCI system error on a component that resides in slot #.	Same as above.	Same as above.	Same as above.
E1714	Unknown Err	Low	BIOS has determined there has been an error in the system but is unable to determine its origin.	AC Cycle or SEL clear	Yes	POST, After POST
E171F	PCIE Fatal Err B## D## F##	High	BIOS has reported a PCIe fatal error on a component that resides in PCI configuration space at bus ##, device ##, function ##.	AC Cycle or SEL clear	Yes	POST, After POST
E171F	PCIE Fatal Slot #	High	BIOS has reported a PCIe fatal error on a component that resides in slot #.	Same as above.	Same as above.	Same as above.

Hard Drives - Message Code: "x18xx"
Message Code	Message String	Message Priority	Message Comments	Minimum Action Required to Remove Message from LCD	Exists in SEL?	System Phase When Event Can Occur?
E1810	HDD ## Fault	Low	Hard drive ## has had a fault as determined by the SAS subsystem.	AC Cycle or SEL clear	Yes	POST, After POST
E1811	HDD ##RbldAbrt	Low	Drive ## has had its rebuild aborted.	AC Cycle or SEL clear	Yes	POST, After POST
E1812	HDD ## Removed	Low	Drive ## has been removed from the system.	System reset or device is reseated/replaced/repaired.	Yes	POST, After POST

Miscellaneous- Message Code: "x19xx"
Message Code	Message String	Message Priority	Message Comments	Minimum Action Required to Remove Message from LCD	Exists in SEL?	System Phase When Event Can Occur?
I1910	Intrusion	Low	The chassis lid has been removed.	Chassis lid is returned to the system.	Yes	Any
I1911	>3ERRsChkLog	N/A	User must check the system event log (SEL) for the rest of the errors on the system .Thee LCD is limited to three error, warning, and/or informational messages at a time based on priority level.	Less than 3 events to display on the LCD.	No	Any
I1912	SEL Full	Med	System Event Log is full of events and because of this is unable to log anymore. You must clear the log in order for the Server Management controller to log any more events.	AC Cycle or SEL clear	Yes	Any
E1913	CPU & Firmware Mismatch	Med	Current version of BMC firmware is incompatible with the Woodcrest processor.	AC Cycle or SEL clear	Yes	POST

BIOS Progress Codes - Message Code: N/A
Message Code	Message String	Message Priority	Message Comments	Minimum Action Required to Remove Message from LCD	Exists in SEL?	System Phase When Event Can Occur?
N/A	POWER	N/A	0x01 -- System power-on.	N/A	No	Any
N/A	MCODE	N/A	0x02 -- CPU Microcode load.	N/A	No	Any
N/A	CINIT	N/A	0x03 -- Chipset Initialization.	N/A	No	Any
N/A	MEMC	N/A	0x04 -- Memory Configuration.	N/A	No	Any
N/A	SBIOS	N/A	0x05 -- BIOS shadow into memory.	N/A	No	Any
N/A	PINIT	N/A	0x06 -- Multiprocessor Initialization.	N/A	No	Any
N/A	START	N/A	0x07 -- POST processing start.	N/A	No	Any
N/A	SMM	N/A	0x08 -- System management interrupt (SMI) initialization.	N/A	No	Any
N/A	PCIEN	N/A	0x09 -- PCI Bus Enumeration & Video initialization.	N/A	No	Any
N/A	VIDEO	N/A	0x40 -- Display sign-on.	N/A	No	Any
N/A	PCIC	N/A	0x41 -- PCI Configuration.	N/A	No	Any
N/A	OS	N/A	0x7F -- Give control to OS.	N/A	No	Any
N/A	E2010	N/A	0x80 -- No memory installed in the system.	N/A	No	Any
N/A	E2011	N/A	0x81 -- Memory detected but is not configurable .Error detected during memory configuration. Could be result of bad memory, mismatched memory or bad socket.	N/A	No	Any
N/A	E2012	N/A	0x82 -- Memory configured but not usable. Memory sub-system failure. Could be the result of bad memory.	N/A	No	Any
N/A	E2013	N/A	0x83 -- BIOS failed to copy its flash image into memory. Could be the result of bad memory.	N/A	No	Any
N/A	E2014	N/A	0x84 -- CMOS failure. CMOS'S RAM not working.	N/A	No	Any
N/A	E1215	N/A	0x05 -- DMA controller failure.	N/A	No	Any
N/A	E1116	N/A	0x80 -- Interrupt controller failure.	N/A	No	Any
N/A	E1217	N/A	0x07 -- Timer refresh failure.	N/A	No	Any
N/A	E1218	N/A	0x28 -- Programmable interval timer error.	N/A	No	Any
N/A	E0119	N/A	0x29 -- Parity error.	N/A	No	Any
N/A	E122A	N/A	0x2a -- SIO failure.	N/A	No	Any
N/A	E122B	N/A	0x00b0 -- Keyboard controller failure.	N/A	No	Any
N/A	E141C	N/A	0x3c -- System management interrupt (SMI) initialization failure.	N/A	No	Any
N/A	E.11	N/A	0xC4 -- BIOS shutdown test failure.	N/A	No	Any
N/A	E.11	N/A	0xC4 -- BIOS POST memory test failure. Could be the result of bad memory.	N/A	No	Any
N/A	E141F	N/A	0xC4 -- Dell remote access controller (DRAC) configuration failure. Check screen for the actual error message.	N/A	No	Any
N/A	E0000	N/A	0xC4 -- CPU configuration failure. Check screen for the actual error message.	N/A	No	Any
N/A	E1221	N/A	0xC4 -- Incorrect memory configuration. Memory population order not correct. Refer to the user guide.	N/A	No	Any
N/A	E1222	N/A	22x -- General failure after video. Check screen for the actual error message.	N/A	No	Any

BIOS Fatal Error Codes - Message Code: "x20xx"
Message Code	Message String	Message Priority	Message Comments	Minimum Action Required to Remove Message from LCD	Exists in SEL?	System Phase When Event Can Occur?
E2010	No Memory	High	0x80 -- No memory installed in the system.	System reset	Yes	POST
E2011	MemConfigErr	High	0x81 -- Memory detected but is not configurable. Error detected during memory configuration. Could be result of bad memory, mismatched memory or bad socket.	System reset	Yes	POST
E2012	Unusable Memory	High	0x82 -- Memory configured but not usable. Memory sub-system failure. Could be the result of bad memory.	System reset	Yes	POST
E2013	Shadow BIOS Fail	High	0x83 -- BIOS failed to copy its flash image into memory. Could be the result of bad memory.	System reset	Yes	POST
E2014	CMOS Fail	High	0x84 -- CMOS failure. CMOS'S RAM not working.	System reset	Yes	POST
E2015	DMA Controller	High	0x85 -- DMA controller failure.	System reset	Yes	POST
E2016	IntController	High	0x86 -- Interrupt controller failure.	System reset	Yes	POST
E2017	Timer Fail	High	0x87 -- Timer refresh failure.	System reset	Yes	POST
E2018	ProgTimer	High	0x88 -- Programmable interval timer error.	System reset	Yes	POST
E2019	Parity Error	High	0x89 -- Parity error.	System reset	Yes	POST
E201A	SIO Err	High	0x8A -- SIO failure.	System reset	Yes	POST
E201B	KybdController	High	0x8B -- Keyboard controller failure.	System reset	Yes	POST
E201C	SMI Init	High	0x8C -- System management interrupt (SMI) initialization failure.	System reset	Yes	POST
E201D	Shutdown Test	High	0xC0 -- BIOS shutdown test failure.	System reset	Yes	POST
E201E	POSTMemTest	High	0xC1 -- BIOS POST memory test failure. Could be the result of bad memory.	System reset	Yes	POST
E201F	DRACConfig	High	0xC2 -- Dell remote access controller (DRAC) configuration failure. Check screen for the actual error message.	System reset	Yes	POST
E2020	CPUConfig	High	0xC3 -- CPU configuration failure. Check screen for the actual error message.	System reset	Yes	POST
E2021	Memory Population	High	0xC4 -- Incorrect memory configuration. Memory population order not correct. Refer to the user guide.	System reset	Yes	POST
E2022	POST Fail	High	0xFE -- General failure after video. Check screen for the actual error message.	System reset	Yes	POST

Special Exceptions - Message Code: "x10xx"
Message Code	Message String	Message Priority	Message Comments	Minimum Action Required to Remove Message from LCD	Exists in SEL?	System Phase When Event Can Occur?
E1000	Failsafe, Call Support	Special	Check System Event Log for critical failure details.	AC Cycle or SEL clear	Yes	Any