SBC-T113产品特性：
-
采用Allwinner公司Cortex-A7双核T113-i处理器，运行最高速度为1.2GHZ；
-
内置64-bit XuanTie C906 RISC-V协处理器；
-
支持JPEG/MJPEG视频编码，最大分辨率1080p@60fps；支持多格式1080P@60fps视频解码 (H.265,H.264, MPEG-1/2/4)；
-
支持RGB666/LVDS/MIPI-DSI，分辨率最高1920x1080；
-
支持512-1G Bytes DDR3 SDRAM；
-
支持SPI NAND存储和启动(默认：256MB；最大1GB)或者EMMC启动(默认：4GB,最大32GB)；
-
支持四路USB2.0 HOST；
-
支持六路RS232通信；
-
支持双路CAN BUS通信（隔离）；
-
支持双路以太网,一路10/100M;一路10/100/1000M；
-
稳定的操作系统的支持，可预装Ubuntu20.04/LINUX 5.4 Preempt/Tina5.0；
-
标准3.5寸主板， 尺寸为:146*102MM；
SBC-T113功能评估图：
T113i主板终端信息_tina5 Linux :
[76]HELLO! BOOT0 is starting!
[79]BOOT0 commit : 069ed30b88
[82]set pll start
[84]fix vccio detect value:0xc0
[91]periph0 has been enabled
[94]set pll end
[95][pmu]: bus read error
[98]board init ok
[100]enable_jtag
[101]get_pmu_exist() = -1
[104]DRAM BOOT DRIVE INFO: V0.34
[107]DRAM CLK = 792 MHz
[109]DRAM Type = 3 (2:DDR2,3:DDR3)
[112]DRAMC ZQ value: 0x7b7bfb
[115]DRAM ODT value: 0x42.
[118]ddr_efuse_type: 0x0
[121]DRAM SIZE = 512 MB
[128]DRAM simple test OK.
[130]rtc standby flag is 0x0, super standby flag is 0x0
[135]dram size =512
[138]card no is 2
[140]sdcard 2 line count 4
[142][mmc]: mmc driver ver 2021-05-21 14:47
[152][mmc]: Wrong media type 0x0, but host sdc2, try mmc first
[157][mmc]: ***Try MMC card 2***
[182][mmc]: RMCA OK!
[184][mmc]: mmc 2 bias 4
[188][mmc]: MMC 5.1
[190][mmc]: HSSDR52/SDR25 4 bit
[193][mmc]: 50000000 Hz
[195][mmc]: 3648 MB
[197][mmc]: ***SD/MMC 2 init OK!!!***
[292]Loading boot-pkg Succeed(index=0).
[296]Entry_name = u-boot
[303]Entry_name = optee
[307]Entry_name = dtb
[310]tunning data addr:0x430003e8
[313]Jump to second Boot.
M/TC: OP-TEE version: 2a99a16f (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016. 05)) #1 Thu Aug 17 11:13:02 UTC 2023 arm
E/TC:0 0 platform_standby_fdt_parse:126 no pmu0 node
E/TC:0 0 sunxi_twi_parse_from_dt:121 no pmu node
U-Boot 2018.07-g6047f84-dirty (Nov 25 2024 - 17:03:09 +0800) Allwinner Technolog y
[00.384]CPU: Allwinner Family
[00.387]Model: sun8iw20
[00.389]DRAM: 512 MiB
[00.392]Relocation Offset is: 1cebd000
[00.420]secure enable bit: 0
E/TC:0 fdt_getprop_u32:336 prop trace_level not found
[00.434]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=300Mhz
[00.440]gic: sec monitor mode
SPI ALL: ready
[00.455]line:703 init_clocks
[00.458]flash init start
[00.460]workmode = 0,storage type = 2
[00.464][mmc]: mmc driver ver uboot2018:2023-07-4 16:18:00
[00.470][mmc]: SUNXI SDMMC Controller Version:0x50310
[00.495][mmc]: Best spd md: 3-HS200/SDR104, freq: 4-150000000, Bus width: 4
[00.502]sunxi flash init ok
[00.504]drv_disp_init
partno erro : can't find partition bootloader
[00.543]drv_disp_init finish
[00.552]Loading Environment from SUNXI_FLASH... OK
[00.564]boot_gui_init:start
partno erro : can't find partition Reserve0
bad fb1_cfg[w=0,h=0,bpp=32,format=0]
[00.581]boot_gui_init:finish
partno erro : can't find partition bootloader
[00.588]bmp_name=bootlogo.bmp size 1843254
[00.635]Item0 (Map) magic is bad
[00.638]the secure storage item0 copy0 magic is bad
[00.646]Item0 (Map) magic is bad
[00.648]the secure storage item0 copy1 magic is bad
[00.653]Item0 (Map) magic is bad
secure storage read widevine fail
secure storage read ec_key fail
secure storage read ec_cert1 fail
secure storage read ec_cert2 fail
secure storage read ec_cert3 fail
secure storage read rsa_key fail
secure storage read rsa_cert1 fail
secure storage read rsa_cert2 fail
secure storage read rsa_cert3 fail
[00.684]usb burn from boot
delay time 0
weak:otg_phy_config
[00.695]usb prepare ok
[00.757]LCD open finish
[00.998]overtime
[01.001]do_burn_from_boot usb : no usb exist
List file under ULI/factory
** Unrecognized filesystem type **
root_partition is rootfs
set root to /dev/mmcblk0p5
[01.019]update part info
[01.021]update bootcmd
[01.025]change working_fdt 0x5c87ce68 to 0x5c85ce68
[01.030][mmc]: can't find node "sunxi-mmc2" try "mmc"
[01.035][mmc]: no mmc-hs400-1_8v!
[01.038][mmc]: get sunxi-mmc2 string failed
[01.043]The storage not support sample function
[01.068]update dts
Hit any key to stop autoboot: 0
boot addr 0x45000000 0x45c66800 exceed dsp0 scope
dsp0 addr 0x45000000 0x45100000
[02.284]no vendor_boot partition is found
Android's image name: sun8i_arm
The loading address of the kernel is not in the boot image
ERROR: reserving fdt memory region failed (addr=41b00000 size=100000)
ERROR: reserving fdt memory region failed (addr=5c907000 size=7e9000)
[02.343]Starting kernel ...
[02.346][mmc]: mmc exit start
[02.363][mmc]: mmc 2 exit ok
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.4.61 (ping@embedall) (arm-linux-gnueabi-gcc (Lina ro GCC 5.3-2016.05) 5.3.1 20160412, GNU ld (Linaro_Binutils-2016.05) 2.25.0 Lina ro 2016_02) #1 SMP PREEMPT Mon Nov 25 16:23:08 CST 2024
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instructio n cache
[ 0.000000] OF: fdt: Machine model: sun8iw20
[ 0.000000] printk: bootconsole [earlycon0] enabled
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] Reserved memory: created DMA memory pool at 0x42200000, size 0 Mi B
[ 0.000000] OF: reserved mem: initialized node vdev0buffer@42200000, compatib le id shared-dma-pool
[ 0.000000] Reserved memory: created DMA memory pool at 0x42244000, size 0 Mi B
[ 0.000000] OF: reserved mem: initialized node dsp0_rpbuf@42244000, compatibl e id shared-dma-pool
[ 0.000000] Reserved memory: created DMA memory pool at 0x42900000, size 0 Mi B
[ 0.000000] OF: reserved mem: initialized node vdev0buffer@42900000, compatib le id shared-dma-pool
[ 0.000000] Reserved memory: created DMA memory pool at 0x42944000, size 0 Mi B
[ 0.000000] OF: reserved mem: initialized node c906_rpbuf@42980000, compatibl e id shared-dma-pool
[ 0.000000] cma: Reserved 8 MiB at 0x5f800000
[ 0.000000] On node 0 totalpages: 129112
[ 0.000000] Normal zone: 1024 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 129112 pages, LIFO batch:31
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.0
[ 0.000000] percpu: Embedded 15 pages/cpu s31040 r8192 d22208 u61440
[ 0.000000] pcpu-alloc: s31040 r8192 d22208 u61440 alloc=15*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 128088
[ 0.000000] Kernel command line: earlyprintk=sunxi-uart,0x02500000 clk_ignore _unused initcall_debug=0 console=ttyAS0,115200 loglevel=8 root=/dev/mmcblk0p5 in it=/init rdinit=/rdinit partitions=boot-resource@mmcblk0p1:env@mmcblk0p2:env-red und@mmcblk0p3:boot@mmcblk0p4:rootfs@mmcblk0p5:dsp0@mmcblk0p6:private@mmcblk0p7:r ootfs_data@mmcblk0p8:UDISK@mmcblk0p9 cma=8M snum= mac_addr= wifi_mac= bt_mac= sp ecialstr= gpt=1 androidboot.hardware=sun8iw20p1 boot_type=2 androidboot.boot_typ e=2 gpt=1 uboot_message=2018.07-g6047f84-dirty(11/25/2024-17:03:09) mbr_offset=1 032192 disp_reserve=8294400,0x5c907000 androidboot.dramfreq=792 androidboot.dram size=512 mtdparts=<NULL> uboot_backup=ubootA
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, l inear)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, li near)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 476208K/516448K available (7168K kernel code, 379K rwdata , 2688K rodata, 1024K init, 199K bss, 32048K reserved, 8192K cma-reserved, 0K hi ghmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jif fies.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] random: get_random_bytes called from start_kernel+0x250/0x3d0 wit h crng_init=0
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 43980 46511097ns
[ 0.008018] Switching to timer-based delay loop, resolution 41ns
[ 0.014210] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_ idle_ns: 79635851949 ns
[ 0.024058] Console: colour dummy device 80x30
[ 0.028556] Calibrating delay loop (skipped), value calculated using timer fr equency.. 48.00 BogoMIPS (lpj=240000)
[ 0.038917] pid_max: default: 32768 minimum: 301
[ 0.043677] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linea r)
[ 0.051016] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.059402] CPU: Testing write buffer coherency: ok
[ 0.064657] /cpus/cpu@0 missing clock-frequency property
[ 0.069976] /cpus/cpu@1 missing clock-frequency property
[ 0.075317] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.081582] Setting up static identity map for 0x40100000 - 0x40100060
[ 0.088274] rcu: Hierarchical SRCU implementation.
[ 0.093381] BOOTEVENT: 93.371957: ON
[ 0.097768] smp: Bringing up secondary CPUs ...
[ 0.103573] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.103726] smp: Brought up 1 node, 2 CPUs
[ 0.113525] SMP: Total of 2 processors activated (96.00 BogoMIPS).
[ 0.119704] CPU: All CPU(s) started in SVC mode.
[ 0.124876] devtmpfs: initialized
[ 0.142347] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.150534] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 19112604462750000 ns
[ 0.160401] futex hash table entries: 512 (order: 3, 32768 byt
扫一扫
4544
被折叠的 条评论
为什么被折叠?
到【灌水乐园】发言
